FloraCap Irrigation System

Can I use the Bubbler with the Micro Dripper Assembly set up?

The QDPS or Bubbler is not needed or compatible with the Micro Dripper setup.

Do I need pvc glue when connecting the QDPS to the pvc pipe?

Yes, you will want to use a pvc glue and primer to connect the QDPS to the pvc pipe. There are very effective 2 in 1s that we prefer, Oatley for example.

How many plants can the Bubbler or QDPS water?

The QDPS can water 8 plants in the following setups: ● 4-6” square matrix and pots ● 7.5-9” round matrix ● 9-10.5” round matrix (3 gallon pot) QDPS can serve 4 plants in the following setups ● 10.5-12 Round Matrix (5 gallon pot) ● 12.5-14.5 Round Matrix ● 15.5-18 Round Matrix And if you close 1, 2 or 4 ports the instructions are above.

What cleaning agents do you recommend for a FloraFlex irrigation system?

GreenClean Acid and Sanidate 5.0 from Biosafe Systems.

What is the difference between Multi and Open Flow Bubbler or QDPS?

The Multi Flow comes with Flow Inserts for the Bubbler heads that determine the volume or GPH per port. The Open Flow is typically double of the 20 GPH (blue), but subject to a higher flow. Open flow is mostly used for the matrix system as the matrix system is designed for larger pots and requires a high volume of water.

What parts are used to make the Open Flow Quick Disconnect Pipe System?

Flora Bubbler, GH to NPT Quick Disconnect, Flora Valve, into the Flora Pipe Fitting, and then into the T or L; You choose...

How do I convert or turn my Open Flow Bubbler into a Multi Flow Bubbler?

The Open Flow Bubbler can be converted to a Multi Flow Bubbler with the Flow Conversion Kit and your desired GPH per port will be determined from your choice of Flow Insert. ● Yellow (2 GPH) ● Black (6 GPH) ● Red (10 GPH) ● Blue (20 GPH)

Can I convert a Multi Flow bubbler into Open Flow?

The Multi Flow Bubbler can be converted to Open Flow by removing the Flow Conversion Kit.

Eight (8)

Do I need the ¾” or 1” Quick Disconnect Pipe System (QDPS)?

If your flow rate is under 23 gpm per zone you can use the ¾” QDPS. If your flow rate is between 23-37gpm go with the 1” QDPS. See Pump Sizing infographic under How To Grow link on the website.

What is the Flora Bubbler female threaded inlet pipe size?

½ inch.

What is the the Flora Valve male outlet pipe size?

3/4 inch.

Do I need to use pvc glue and primer when connecting pvc pipe to the T or L Flora Pipe Fittings?

Although it is a snug fit, you will still need to use PVC glue/adhesive, primer, and/or a 2 in 1 alternative. https://www.youtube.com/watch?v=wmoSCbOFcMs

What is the maximum PSI of the/a Flora Valve?

105 PSI

What is the minimum and maximum operating temperature of the Flora Valve or the entire QDPS or Bubbler?

40° - 140° F

What is the manual valve used for on the Flora Valve?

Restrict Flow, Increase pressure, Manually turn on and off the water flow.

Is the Quick Disconnect Pipe system or a Bubbler made out of Food Grade plastic?

Yes, it is BPA and lead-free virgin material.

What size tubing connects to the Flora Bubbler barbed ports?

¼” tubing.

What causes uneven flow with the Quick Disconnect Pipe Systems?

It may be one or multiple things from the list below. 1. Improper pump size, typically too small of a pump. 2. ¼” tubing cut different lengths, they all must be cut the same length throughout the system. 3. Not using an Air Bleed Valve.

Why is my manifold, bubbler, or QDPS leaking?

There is a threaded male piece that goes into the female threaded bottom of the bubbler. On this piece there is an O-Ring which provides a tight seal. Simply tighten this until you can no longer see the black O-Ring.

Please, mind that only logged in users can submit questions

Your question:

Your name:

get notification on email when the answer is ready

Your e-mail: